![]() ![]() ![]() They are also a lot more attractive than a simple pipe and in the event you need to replace or change a plumbing fitting, you only need to drain the overflow box instead of your entire tank.Įvery tank has evaporation and in a tank without an overflow, sump, etc that happens right in the aquarium and is noticeable in the display. This helps to keep algae and your critters out. If you have an overflow, that’s still going to be the case except your aquarium critters aren’t exposed to the very small/high flow area, its being spread out across all the teeth on the 3 sides of the overflow so each tooth has a significantly less flow. At your 1” drain you have a 1” area that has 500gph flowing through it. Say your return pump is pumping 500gph, so therefore 500gph is going over the teeth and into your 1” drain. The overflow box and its teeth disperse the flow to a much wider area. That said though, the overflow offers a bit more flexibility and protection. You might be asking yourself why don’t I skip the overflow and just put a drain pipe in. This way the height of the water in the tank will not exceed the height of the overflow and when the power goes off the tank will only drain until it reaches the top of the overflow (though be careful about back siphons down your return pump line). The excess water flows over and then proceeds down the drain and into the sump. The only way water goes over and into the overflow is if the water level in the main tank exceeds the height of the overflow. You have the high water side of the dam (inside the tank) and the low water side (inside the overflow where the drain is). The top of the dam is the overflow teeth. When you setup an overflow in a tank you are essentially creating a dam. Really this concept is just gravity at work. One of the biggest benefits (and most misunderstood concepts) of an overflow is how they maintain steady water levels in the display tank and are self-regulating. The principles with an external overflow are the same, just the means of getting water over the side of the tank is different and I will get into more detail with towards the end. For the purpose of explaining overflows I am going to use the internal overflow as the example. First is the internal overflow and second is the external overflow. Your typical self-installed overflow will fall into one of two categories. If you’re more interested in how the concept works, then keep reading! In the case of an internal overflow, it’s worth mentioning that you want to make sure you have enough room for any fittings you plan to install as well, but generally speaking they are all sized to house typical size plumbing fittings anyway. If you have a return pump that’s going to be 500gph, get an overflow rated for at least 500gph, as long as the overflow is big enough it will self-regulate itself to any pump slower. If you’re looking for the simple answer to “What size overflow do I need?” The answer is: Purchase an overflow that is rated for more flow (generally rated in Gallons per Hour) then your return pump will be. I think the hesitation and the question comes in from the fact that how an overflow system works seems complicated though, like most things, once explained it turns out to be pretty simple. One of the most common questions I see is “How big of an overflow do I need to buy” and it’s a bit ironic because the answer is so much simpler than most folks expect it to be. They allow you to hide all your ugly equipment outside of your display tank, allow you to use bigger, better, and more equipment, and they make for a steady water level in your display tank. Just lower the overflow box onto your aquarium and then connect your favorite type of plumbing to the included 1" bulkhead.Overflows are great. Hang on back overflows do require more monitoring and safety precautions to be in place, but can be completely reliable if installed properly and maintained regularly. Installation only takes a couple of minutes, and the PF-300 only requires 3" of clearance outside the tank to drain water down to a sump, refugium, or wet/dry filter. In most cases, we would recommend drilling your aquarium and using an internal overflow like the Eshopps Eclipse, but in some situations, a HOB style overflow may be the best option. Traditional overflows require you to drill holes in your aquarium where Eshopps PF HOB overflows use a siphon to draw water over the wall of the tank without any modifications to your aquarium. Adding a sump to a tank will allow you to hide equipment and while adding water volume making your tank more stable. Add an overflow to any aquarium with Eshopps PF series of hang on back overflows. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |